Ice Maker Repair
Same-day repair service for all kinds of ice makers. Call us now to get your ice maker back to work as it should.
Types of Ice Maker We Repair
The ice-maker is a great invention, which we usually take for granted, even during the hottest days of summer. It helps us to keep fresh ice on hand for everyday use. If something goes wrong with your appliance, do not get upset. Call Ramics Repair at (888) 977-5657 to schedule a service appointment and we will get your ice-maker working properly again as soon as possible.
- Built-in Ice Makers
- Under Counter Ice Makers
- Free-standing Ice Makers
Common Ice Maker Issues
Our technicians have the expertise needed to troubleshoot and repair your ice maker, regardless of the problem. Listed below are the most frequent issues we see:
Temperature Is Too Low
The ice-maker will not produce ice cubes efficiently if the freezer temperature is too high. Ideally, the temperature should be set between 0 and 5° F or -18 and -13° C. If the freezer temperature stays above 15° F, there is probably something wrong with the appliances cooling system. This can be caused by accumulated debris on the condenser coils, preventing the coils from properly dissipating heat. The failure of the condenser fan motor to properly circulate the air, or frosted over evaporator coils restricting airflow. The evaporator coils being frosted over, indicates a failure in the defrost system, which is caused by a defective defrost control, heater or thermostat.
Defective Water Inlet Valve
The refrigerator’s water inlet valve controls the water being sent to the icemaker tray. The inlet valve can fail both mechanically and electrically. A mechanical failure could be caused by the build-up of mineral deposits, preventing the valve from opening. If this happens, you will need to replace the valve. Trying to clean out an old valve is not recommended due to the risk of part failure after repair. To determine if the inlet valve has failed electrically, use a multi-meter to test the valve solenoid coils for continuity. If one or more of the coils tests negative for continuity, the inlet valve will need to be replaced.
Low Water Pressure
To operate properly, the water inlet valve requires between 20 and 120 PSI. To help determine this, shut off the water supply, disconnect the supply line from the inlet valve and hold the line over a bucket. Turn the water supply back on, in a serve whether or not there is a strong flow of water jetting out of the line. A weak flow indicates a problem with the water line or the water supply valve.
Frozen Water Supply Tube
A frozen water supply tube leading to the icemaker tray can also prevent the ice-maker from working. You can thought the supply tube by heating it with a hairdryer, but be aware that a frozen supply tube is usually caused by insufficient water pressure or a defective inlet valve.
Faulty Door Switch
The door switch disables the ice dispenser when the refrigerator door is open. A faulty door switch will prevent the dispenser from working, even when the door is closed. As with the water inlet valve solenoids, you can use a multi-meter to test the door switch for continuity to determine if the part has failed or not.
Malfunctioning Ice-Maker Assembly
One of the components inside the ice-maker assembly itself could be malfunctioning. Since these components are usually not sold separately, you will need to replace the entire assembly.
Dirty Ice Bin
If the container, where the ice is stored, becomes dirty, ice will have a bad odor and taste. Unscrew, wash and dry the ice bin. Reassemble it and check if the problem has been resolved.
Old Food In The Refrigerator
Remove any old food from your refrigerator and wash all interior surfaces of the freezer and fridge compartment with vinegar and water solution, then dry. Check if it has helped to resolve the issue.
Clogged Water Filter
A bad odor or taste may mean it is time to change the filter. It is recommended that the water filter be replaced every 6 months or more often depending on use. Replace the filter with a new one suitable for your refrigerator model.
What Our Customers Say About Us
Repair of All Appliance Brands
We service over 70 brands, so you don’t need to call two companies if you own appliances from different brands. These brands include Amana, Bosch, Dacor, DCS Fisher & Paykel, Frigidaire, GE, Jenn Air, Electrolux, KitchenAid, Liebherr, LG, Maytag, Miele, Thermador, Sub-Zero, Samsung, Sears Appliances –Kenmore, Viking, Whirlpool, Wolf and many more. Most of our repair bookings for appliance repairs are attended on the same day.
FAQ
Why is my ice maker not making ice?
The cause may be a warm freezer, shut-off setting, frozen fill tube, clogged filter, low water pressure, failed inlet valve, sensor, ice-maker assembly, or control problem.
Why is my ice maker producing small or hollow cubes?
Restricted water flow, low water pressure, an old filter, partially frozen fill tube, or failing inlet valve can reduce the amount of water entering the ice mold.
Why is my ice maker leaking water?
A loose connection, cracked water line, failed inlet valve, misaligned fill tube, overflowing ice mold, drain problem, or internal reservoir leak may be responsible. Shut off the water supply if the leak is active.
Do you repair refrigerator ice makers and standalone ice machines?
We service many refrigerator ice makers and built-in, under-counter, and freestanding ice machines. Provide the model number and installation type so we can confirm service.
How long should an ice maker take to start producing ice?
After installation, repair, or a temperature change, many units need several hours to cool and begin cycling, and up to about 24 hours for normal production. Exact timing varies by model and operating conditions.